Logo

U0155 Engine Trouble Code

U0155 Engine

When you check engine light came on code U0155 the reason should be . However your vehicle's manufacturer may have a different definition for the U0155 OBD-II Diagnostic Network (U) Trouble Code. So you should chech it on our car models.

U0155 code can be about changing a broken oxygen sensor can lead to a busted catalytic convertor which can cost upwards of $1,300. Taking your vehicle into a service shop will cost you around $300 depending on the vehicle. But, an oxygen sensor is easy to replace on many vehicles and is detailed in the owner's manual PDF or in our website. If you know where this sensor is located, you only have to unclip the old oxygen sensor and replace it with a new sensor. Regardless of how you approach it, you should get this fixed right away.

U0155 Code Meaning :

U
OBD-II Diagnostic Network (U) Trouble Code For Engine
0
Intake Valve Control Solenoid Circuit Low
1
Engine Oil Temperature Sensor Malfunction
5
Turbocharger Boost Sensor A Circuit Low
5
Shift/Timing Solenoid Malfunction/ 3-2 Shift Solenoid Circuit Electrical

The oxygen (02) sensors on your car measure the oxygen in the exhaust to determine how rich or lean the ratio of fuel and air are in the cylinders. Optimizing this mixture means better fuel economy and fewer exhaust emissions.

U0155 OBD-II Diagnostic Network (U) Trouble Code Description

U0155 engine trouble code is about Shift/Timing Solenoid Malfunction/ 3-2 Shift Solenoid Circuit Electrical. Engine Oil Temperature Sensor Malfunction and Turbocharger Boost Sensor A Circuit Low causes most of code U0155.

Reason For U0155 Code

The reason of U0155 OBD-II Engine Trouble Code is Engine Oil Temperature Sensor Malfunction.

U0155 DTC reports a sensor fault, replacement of the sensor is unlikely to resolve the underlying problem. The engine error is most likely to be caused by the systems that the sensor is monitoring, but might even be caused by the wiring to the sensor itself.

How To Repair U0155 Code

Before starting let's see U0155 repairing process steps:

  • Qualified technicians will begin by using a scan tool to access U0155 code stored in the ECU.
  • Technicians will note U0155 code present and any freeze frame data associated with them.
  • After all, if you sure the engine trouble is finished, the code will be cleared.

The reductant injector is part of the system that reduces the gas that is expelled through either the catalytic converter in gas engines, or the particulate filter in diesel engines. There are sensors in the exhaust system, used by the reductant injector to input voltage readings to the PCM.

U0155 code is stored again, the mechanic will perform a visual inspection of the pressure control solenoid and related systems. If any circuits or connections are damaged or loose, they will resolve these issues and move on to retest the system.

Sometimes U0155 code comes with U015500 code.

Diagnosis Of Engine Error OBD Code U0155

It's essential to diagnose this trouble code. Then are some way which a handyperson should follow for diagnosing the problem that started a U0155 trouble code to be stored

The first step is introductory and is about reacquiring all the canons that have been set. For this, the individual scanner will have to be plugged into the individual harborage of your vehicle. Make sure you indurate frame the data. Any canons that were set previous to the U0155 code will have to be sorted first, as they may have been the reason for the law to set in the first place. It's always good to rule that out.

The coming step is to run a introductory examination of all the electrical circuits, connectors, wiring etc for damages similar as becks, erosion, fraudulent legs etc. All of these will have to be repaired or replaced. After that's sorted, clear the canons and go on a test drive to see if it resets. In case it resets, you'll have to continue your opinion. Depending on your vehicle you may have a vacuum operated selector or a vacuum solenoid if it's electrically actuated. In the case of the former, a hand held vacuum pump will have to be used to testit.The purpose is to see if the internal stopcock is getting turned by the selector, motor or solenoid. In order to do this, a command can be transferred to the system with scanner or by driving the vehicle under the special conditions that will spark the system. While this is passing keep an eye on the checkup tool data for the result.

All Engine Trouble Codes

All engine trouble codes with P, U, B and C engine codes.

Code Search

Please fill the "Code Box" to find engine fault code.

Example: 0140

Car Models :

Please select your car.

How To Read Engine Codes ?

Ways to read engine trouble codes.

How To Clear Check Engine Lights ?

Ways to clear check engine light on car panel.

Check Engine Light Dictionary

Ways to clear check engine light on car panel.